<td id="jc9zf"><ruby id="jc9zf"></ruby></td>

  1. <object id="jc9zf"><strong id="jc9zf"><xmp id="jc9zf"></xmp></strong></object>
    <tr id="jc9zf"><label id="jc9zf"><listing id="jc9zf"></listing></label></tr>

      Product Traceability 

      Introduction
      CRP believes that product traceability is a valuable feature of finished products when one is serving markets with both process and safety critical items. From a process perspective the customer often wants confidence in knowing the materials of construction and that the supplier has undertaken certain materials testing. In order to obtain proof of materials and testing, customers often request materials certification for product. Whilst CRP are capable of and often do provide such certification, the business set out some time ago to try to eliminate this costly and essentially “non-value added activity” whilst still providing the ability to prove materials and testing. Similarly, if for any reason a product fails in service, it is often valuable to trace its manufacture and test as part of the investigation into the cause of failure. For these reasons CRP has developed a comprehensive system for tracing product back through its manufacturing tests and processes to the raw materials without needing to burden the customer with the cost and management of documentation.
        

      PTFE Lined Piping

      Lined piping is produced through a number of manufacturing and test stages—see the diagram below.


       
      Raw Materials
      PTFE fine powder is delivered in 25kg tubs, each marked with the manufacturers batch reference.  This batch reference represents one lot in terms of product testing and manufacturer’s test results refer to this batch number.  Similarly the isoparaffin used as a processing aid is also linked through a batch number to its materials test certificate.


      Mixing
      Discrete amounts of PTFE and isoparaffin are mixed cold.  A mixing log records the amounts of each material used, the mixing conditions, operator and batches used.  The key data is also placed on a label on each mixed tub of material.




      Extrusion
      After warm conditioning the material is selected for extrusio n and the data collected from the material tubs and mixing log is transferred to the extrusion record sheet.  Each batch of a particular PTFE liner size—bore and wall thickness has an extrusion record sheet created for it.  At this stage an extrusion reference is allocated to the batch and entered on the extrusion record sheet in the format shown below.
      For example the second batch of the day on Wednesday, week 45, 2012 made on extruder E would have the reference E23452.






      Sintering
      The extrusion record sheet accompanies the oven sintering process and holds all of the extrusion data, mixing data and that relating to the sinter cycle.  During the sinter cycle an oven trace is recorded, and this is put with the extrusion record sheet.  After sintering each length of liner is marked with the extrusion reference, and a test piece is taken to the test room together with the extrusion record sheet and oven trace.

      Test
      Mechanical properties are tested for each test piece, both ultimate tensile strength and elongation at break.  This is undertaken for ten samples from the test piece, five in the longitudinal direction and five in the cross direction.  The specific gravity of the test piece is calculated and dimensional checks made.  These records are held against the extrusion reference.

      Pipe Lining
      When a length of liner is selected for inserting into the steel tube the liner reference is hard stamped onto one flange of the pipe spool.


      Finished Spool
      The finished pipe spool is subject to a 29 bar hydrotest and for virgin PTFE an electrostatic test at 25kVa.  These test results are recorded against both the customer order reference and the extrusion reference.

      PFA Lined Fittings
      Lined fittings have fewer manufacturing stages than PTFE lined pipe—see the diagram below. 



      Raw Materials
      PFA is delivered in 25kg tubs, each marked with the manufacturers batch reference.  Again this represents one lot in terms of product testing and material certificates provided by the manufacturer and their test results refer to this batch number.

      Moulding
      Specific batches of material are used for moulding and no two batches are ever mixed.  A moulding record sheet identifies the batch number of polymer and allocates a simple sequential reference, preceded by the letters PFA and followed by a two digit year as below.


      For example the 1456th moulding made last year would be PFA 1456 11.

      Trimming
      The finished moulding is stripped from it's tooling and trimmed.

      Test
      Following a visual inspection the component is subject to an electrostatic test at 25kV and/or a hydrotest at 29 bar.  At this point the component is stamped up with its mould reference.  The test results are entered onto the moulding record sheet.


      Conclusion
      This method of product identification enables product in the field to be married up with the product materials and test records in the event of any concern or required investigation; without putting the onus on the customer to find paper based records and try to reconcile them against physical plant.

       




         

      Contact Details

      Corrosion Resistant Products Ltd
      Todmorden Road
      Littleborough
      OL15 9EG

      Phone: +44(0)1706 756400
      Fax: +44(0)1706 379567
      Email:

       






      真人金花游戏